-
1 Festigkeitsbedingung
условие прочности
Определённое значение напряжения или комбинации напряжений, при котором не происходит разрушения тела
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]Тематики
- строительная механика, сопротивление материалов
EN
DE
FR
Немецко-русский словарь нормативно-технической терминологии > Festigkeitsbedingung
-
2 Kurzschlussstrom (einer Zelle oder Batterie), m
ток короткого замыкания химического источника тока
ток короткого замыкания
Максимальное значение тока разряда химического источника тока при коротком замыкании внешней цепи.
[ ГОСТ 15596-82]
ток короткого замыкания
Максимальный ток, отдаваемый батареей в цепь с минимальным сопротивлением по сравнению с сопротивлением батареи в заданных условиях.
[Инструкция по эксплуатации стационарных свинцово-кислотных аккумуляторных батарей в составе ЭПУ на объектах ВСС России. Москва 1998 г.]EN
short-circuit current (related to cells or batteries)
maximum current which should be delivered by a cell or battery into an external circuit with zero electric resistance, or an external circuit which depresses the cell or battery voltage to approximately zero volt
NOTE – Zero electric resistance is a hypothetical condition and in practice the short-circuit current is the peak current flowing in a circuit of very low resistance compared to the internal resistance of the battery.
[IEV number 482-03-26 ]FR
courant de court-circuit (d’un élément ou d’une batterie), m
courant maximal que pourrait fournir un élément ou une batterie dans un circuit extérieur de résistance électrique nulle, ou un circuit extérieur qui abaisse la tension aux bornes de l’élément ou de la batterie approximativement à zéro volt
NOTE – Une résistance électrique nulle est hypothétique et en pratique, le courant de court-circuit est le courant de crête circulant à travers un circuit de résistance très faible par rapport à la résistance interne de la batterie.
[IEV number 482-03-26 ]Тематики
Классификация
>>>Синонимы
EN
DE
- Kurzschlussstrom (einer Zelle oder Batterie), m
FR
- Kurzschlussstrom (einer Zelle oder Batterie), m
Немецко-русский словарь нормативно-технической терминологии > Kurzschlussstrom (einer Zelle oder Batterie), m
-
3 die Beständigkeit
- {constancy} sự bền lòng, tính kiên trì, tính kiên định, tính trung kiên, sự trung thành, sự chung thuỷ, sự bất biến, sự không thay đổi - {continuance} sự tiếp tục, sự tồn tại, sự kéo dài, sự lâu dài, sự lưu lại lâu dài, sự tiếp tục tình trạng, sự hoãn, sự đình lại - {duration} thời gian, khoảng thời gian - {faithfulness} lòng trung thành, lòng chung thuỷ, tính trung thực, tính chính xác - {permanence} sự lâu bền, sự vĩnh cửu, sự thường xuyên, sự thường trực, sự cố định, tính lâu dài, tính lâu bền, tính vĩnh cửu, tính thường xuyên, tính cố định, cái lâu bền, cái thường xuyên - cái cố định - {stability} sự vững vàng, sự vững chắc, sự ổn định, sự kiên định, sự kiên quyết, tính ổn định, tính bền, độ ổn định, độ bền - {steadiness} tính vững chắc, sự điều đặn, sự đều đều, sự bình tĩnh, sự điềm tĩnh, tính đứng đắn, tính chín chắn = die Beständigkeit [gegen] {resistance [to]}+ = die Beständigkeit (Wetter) {settled condition}+ -
4 Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Dauerstrombelastbarkeit, f
-
5 Strombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Немецко-русский словарь нормативно-технической терминологии > Strombelastbarkeit, f
См. также в других словарях:
RÉSISTANCE DES MATÉRIAUX — La résistance des matériaux est la science du dimensionnement. Concevoir une pièce mécanique, un ouvrage d’art ou tout objet utilitaire, c’est d’abord imaginer les formes et le squelette géométrique qui remplissent les fonctions demandées; c’est… … Encyclopédie Universelle
Condition de la Femme en Iran — Condition des femmes en Iran Image t … Wikipédia en Français
Condition de la femme en Iran — Condition des femmes en Iran Image t … Wikipédia en Français
Condition des femmes sous le Troisième Reich — La condition féminine sous le Troisième Reich se caractérise par une politique visant à cantonner les femmes dans un rôle de mère et d épouse et de les exclure de tout poste à responsabilité, notamment dans les sphères politiques ou… … Wikipédia en Français
Résistance — Cette page d’homonymie répertorie les différents sujets et articles partageant un même nom. Sur les autres projets Wikimedia : « Résistance », sur le Wiktionnaire (dictionnaire universel) Sommaire … Wikipédia en Français
Resistance (V TV series) — This is a list of the known members of the Resistance, a fictional worldwide movement comprised of a large number of groups dedicated to fighting the Visitors in the Science Fiction television series V. The Atkins Ellen Baker is the younger… … Wikipedia
Resistance, Rebellion, and Death — Infobox Book name = Resistance, Rebellion, and Death author = Albert Camus publisher = Random House release date = 1960 isbn = Resistance, Rebellion, and Death is a 1960 collection of essays written by Albert Camus and selected by the author… … Wikipedia
Condition des femmes sous la République de Weimar — La condition féminine sous la République de Weimar concerne la place de la femme allemande dans la société, entre 1919 et 1933. Sommaire 1 Les femmes à la sortie de la Première Guerre mondiale 2 L’égalité politique avec les hommes … Wikipédia en Français
Underground Resistance — Logo vom Underground Resistance Underground Resistance (kurz UR) ist ein US amerikanisches Label und Musikprojekt aus Detroit. Inhaltsverzeichnis 1 Biografie … Deutsch Wikipedia
Psychological resistance — is the phenomenon often encountered in clinical practice in which patients either directly or indirectly oppose changing their behavior or refuse to discuss, remember, or think about presumably clinically relevant experiences.Psychoanalytic… … Wikipedia
Insulin resistance — Infobox Disease Name = Insulin resistance Caption = DiseasesDB = ICD10 = ICD9 = ICDO = OMIM = MedlinePlus = eMedicineSubj = med eMedicineTopic = 1173 MeshName = Insulin+Resistance MeshNumber = C18.452.394.968.500 Insulin resistance is the… … Wikipedia
